Hi everyone!

I would just like to say well done to all of the people who were involved in making the 2. gen S-tog, especially BlackChart.
The model and textures are very accurate and the sounds are almost perfect.
It's also good to have so many variations rather than just 1 trainset.

I have have a few problems/things which annoy me though. Firstly, I cannot use the MM-FS consists for driving in activities, because there are no 'passengers' in the eng files and therefore the train cannot stop at stations. Also, the trains seem a bit too fast and accelerate quite fast too - I thought the top speed was 100km/h, but they go up to 116km/h! Finally, the cabview is too high up from the ground (though this is less important).

I'm sorry if you already know of these problems or I have upset you by pointing them out, but they aren't very big problems for an otherwise perfect model for MSTS.

I really like the S-train much. But sadly the old 2.g S-train is not used on many S-train routes anymore.

Many of them have been replaced by the new 4.g S-train...

I like the program to change the destination Sign at the front

I'm working on an update allready, with some of the bugs fixed...
Besides I hope for at photo realistic cab for it with the next release...

The passenger thing is a little OOPS thing I'll change that in the update...
The speed I've had some trouble with...In the .eng files it's set to 100 km/h :?

Sounds good, BC!

Yes it's a shame they are getting rid of the 2.g. S-trains as I have been on them every time I have been to Denmark since I was born (OK I can't remember that far back but I'm sure I did. That was when my mother's uncle was the stationmaster at Vesterport .)
The new ones have only been on the lines I go on since I was in Denmark at Christmas (lines C, H, H+).

For the consists with no passengers:
Open MM and FS eng files with wordpad.
Add under the line BrakeDistributorTrainPipeControlRatio ( 2.03 ):
PassengerCapacity ( 70.0 )
Save.
Your MM-FS will became a passenger train and stop at the stations in the activities you make.
There is the same midstake in some Eng files like DB ICE 406 and other...
Nota Bene: I tell 70 for passenger capacity but you can write whatever you want... I don't know what is the real capacity passenger for the MM or FS unit

There are 3 versions of the MM+FS version, one has 130 seats, another 121 and another 114. It's probably because in some revisions the seating is 3+2 and others it is 2+2.

Så er der dem der kan blære sig med at ha kørt Et 2.G og et 4.G! Heh.. og ikke kun i MSTS..

Øhhhh blære sig ??? hvor ? :roll:

Også i TRS !?

TRS? hva mener du?

RT så vel

Så er version 2, med rigtigt cab samt "trillefløjte" uploadet til siden...

Bare en skam trillefløjten ikke virker

Hilsen Poul

har du prøvet b tasten poul :lol: :lol: :lol: :lol:

Som der står i readme filen skal den aktiveres ved at trykke på 'B' tasten...Den virker fint på den udgave jeg har lavet installationen ud fra

Naturligvis bruger jeg B og mellemrumstasten, men jeg kan altså ikke høre trillefløjten hverken ved taste B eller mellemrums tasten

Jeg har et Sound Blaster Audigy 2 ZS lydkort kan det være årsagen

Er der ikke andre der har det samme problem ???

Venlig hilsen
Poul

Hej Poul
Det er ikke en almindelig trillefløjte du hører på b-tasten, det er den elektroniske fløjte som sidder i S-toget